2024-09-05
Harness companies should continue to technological innovation, always take innovation as the soul of enterprise competitiveness. Enterprises need to be based on the needs of the target market, to prov...
2024-09-05
The role of automotive wiring harness in the whole car is to transfer or exchange power signals or data signals of the electrical system to realize the functions and requirements of the electrical sys...
2024-09-05
Let the compressed air buffer, so that the air supply is more stable, reduce the frequent startup of the wire harness processing, so that the compressed air in the storage tank precipitation, more con...
2024-09-05
At the exhibition site of the conference, domestic and foreign car companies such as Changan Deep Blue, BAIC Foton, South Korea's Hyundai, and Japan's Toyota brought brand-new hydrogen-power...
2024-09-05
The working environment of the cabin is also worse, especially in rainy and snowy weather, and the road condition is not good, so it is more affected by the environment. Most of the branches are also ...
2024-09-05
Centrifugal wiring harness processing principle of operation and maintenance troubleshooting: wiring harness processing inlet guide vane and air release valve for disassembly inspection and action tes...
2024-09-05
There are many pins inside the board-to-board connector interface, so in the daily use of the connector, please pay attention to keep these sockets clean, otherwise the board-to-board connector will b...
2024-09-05
The use of avionics connectors has very high environmental requirements, for example, if they need to be used in high-altitude, low-voltage environments, then the product needs to be specially treated...
2024-09-05
Thus, in summary, a connector-based approach to aspect-oriented modeling allows for the introduction of AOP in the analysis and design phase of software in a way that is transparent and guides the wri...
2024-09-05
Connector wear and tear: Repeated connecting and disconnecting of connectors may cause the contact metal to wear and corrode due to exposure to irritating elements such as water, dust, dirt, etc., res...
2024-09-05
Because board-to-board connectors are soldered, it is generally not possible to observe the quality of the connector's solder joints with the naked eye. Therefore, it is necessary to use a conven...
2024-09-05
How to reduce jack and pin wear: 1, the thicker the nickel layer, the stronger the abrasion resistance of the gold-plated layer. 2, the smoother the surface, the lower the surface roughness, the lower...
2024-09-05
To the board connector in the design and production of the key place is the terminal, it is equivalent to a small connector, can be some of the same or different performance of the device connected to...
2024-09-05
With the in-depth application of MDB technology, the enterprise's design method has changed from the traditional two-dimensional drawing to the design based on three-dimensional models, and has g...
2024-09-05
In automotive applications, the wiring harness failure potential is strong, but the failure of the hazardous advantage is very large, especially the wiring harness overheating and wiring harness short...
2024-09-05
In today's world is the world of high technology, a variety of electronic devices have long been into our lives, this commodity to facilitate our daily life, change the old habits of the past, pr...
2024-09-05
Automotive wiring harness industry in the field of automotive parts belongs to the flexibility of the industry is very large, involving the change is usually very frequent, such as automobile factory ...
2024-09-05
The wiring harness manufacturing process is time-consuming, difficult and task-oriented. Nonetheless, as the demand for wire harnesses and cable assemblies grows, so does the manufacturing of these co...
2024-09-05
A wiring harness, also known as a cable harness, is a component formed by bundling multiple electrical connections (power supply, signal communication) required to connect electronic devices into a bu...
2024-09-05
Miniaturization of connectors - As connectors usually work in a variety of harsh environments and conditions, reliability must be the primary technical requirements of industrial connectors. Only reli...
